FS-Curtis and Arizona Air Compressor are proud to be the sponsor of Matt Ludlow aka Coldwater Kid. Check out some behind the scenes footage of the Coldwater Kid and the whole Top Fuel Race Team.
The Coldwater Kid Top Fuel team is heading into their seventh season of competition in sand drag racing. The Family operated team from Litchfield Park, Arizona is owned by Dwight Ludlow with his son Matthew piloting the 300” nitro-burning Top Fueler. They are three-time Dome Valley Top Fuel Shootout champions (2009, 2011, and 2013). At the 2013 Dome Valley March Madness event, Matthew piloted the Hemi-powered Fueler to his career best pass with a sizzling 2.301/162MPH blast. They also recorded the Quickest Run for Top Fuel in the 2011 race season with a 2.308/158MPH run in the final round of that season's Dome Valley Top Fuel Shootout. This team has also been featured on SPEED Channel's "Lucas Oil On The Edge" & Fox Sports Net's "Race Freaks" TV Shows during the Inaugural Dirt 300 Nitro Nationals in Albuquerque, NM. At this event, the Coldwater Kid team earned a solid runner-up finish.
Thanks you to the Coldwater Kid Racing Team (Matthew Ludlow (Driver), Dwight & Marie Ludlow (Car Owners), John Aleman (Crew Chief), and Jim Green / Charlie Starns (Crew)
Small adjustments can reduce your operating pressure and energy costs while improving flow rates and output. Learn the final steps you can take to optimize your compressed air system and save energy costs. Make sure that you also know the first 5 things you can learn to "Save your Compressed Air System Operating Costs"
- Review Piping Infrastructure. Many systems aren't optimized.
A piping system design should optimize transfer of compressed air at the desired flow and pressure to the point of use. Increasing the size of a pipe from two to three inches can reduce pressure drop up to 50 percent. Shortening the distance air has to travel can further reduce pressure drops by about 20-40 percent.
The more flow through a pipe the greater the pressure drop will be. Pressure drop in a pipe increases with the square of the increase in flow, which means if the flow is doubled, the pressure drop will increase four times. Air distribution piping should be large enough in diameter to minimize pressure drop.
How can FSC features and benefits help with this step? If your compressed air piping system was installed years ago when your compressor was much smaller, this might be an indication that the distribution pipes are too small. A quick guide is to look at the air compressor outlet size. If your distribution piping is smaller than your air compressor outlet size, then it may be time to get your FS Curtis Distributor in to evaluate your piping system. If up-grades are needed, FS Curtis offers a modular, aluminum piping system that is easy to install and is a cost effective alternative to copper or steel piping.
- Change Filters Systematically. Not every once in a while.
Inspect and replace filters systematically to ensure the quality of your air and prevent pressure drops. Go beyond the air compressor and compressor room. There are several air-line and point-of-use filters within the facility. Those are just as important to maintain as the air compressor and air compressor room filters.
How can FSC features and benefits help with this step? Your FS Curtis Distributor will provide you with a complete Filter Package located on your compressed air system supply side. Your process and type of equipment used will determine the level of air quality needed. If you are not sure what you need, ask your FS Curtis Distributor who can guide your selection using an industry standard selection chart.
- Recover Heat. Compressing air generates heat - reuse it!
It's simple physics that compressing air gives off heat, and as much as 90 percent of that heat can be recovered for use in your operation. For example, you can produce hot water for washrooms or direct warm air into a workspace, warehouse, loading dock, or entryway. The savings can really add up.
How can FSC features and benefits help with this step? A simple heat recovery step can be making sure the hot air from your compressor room is directed into a nearby work space. If you have a larger rotary screw compressor with and e-COOL® Technology, you may find capturing the exhaust air from your air compressor and ducting into your facility during the heating season. More aggressive heat recovery systems can be used to pre-heat water or process materials if you operate larger compressor systems.
- Emphasize Proper Maintenance. Ignoring maintenance costs more.
As with most industrial machinery, a compressor runs more efficiently when properly maintained. Proper compressor maintenance cuts energy costs around one percent and helps prevent breakdowns that result in downtime and lost production. Protect your reputation and profits with proper maintenance.
How can FSC features and benefits help with this step? Your FS Curtis i-Command® Touch Control will help monitor your compressor for items needing maintenance as well as sending signals showing maintenance alerts. Having your FS Curtis Distributor establish a scheduled service interval based on the number of hours your compressor runs per year will save you money in the long run. Take advantage of your Extended Warranty by using correct parts and lubricants at the correct time. If you skip service and don’t do maintenance, then you can expect that future warranty claims if needed, may be rejected. Just like you car, if you don’t take care of it, it won’t take care of you!
- Identify and Eliminate Inappropriate Uses of Compressed Air.
Inappropriate uses of compressed air include any application that can be done more effectively or more efficiently by a method other than compressed air. For example, high pressure air often is used for cooling or applications where much lower air pressure is required.
How can FSC features and benefits help with this step? Your FS Curtis Distributor can help you with this. If you have a Compressed Air Leak Survey scheduled, the Auditor normally is looking for inappropriate uses of compressed air at the same time. Common mis-uses are: blowing off a work station with an air gun instead of using a hand brush; using an air stream as a personal cooler instead of a fan; Plus many, many more ways…..
The first step to reduce compressed air energy costs is to measure and monitor your compressed air system's energy consumption, flow rates and operating air pressure. Your FS-Curtis Distributor can help you with your understanding of your compressed air system through an assessment or audit of your system. The FS-Curtis Distributor will provide you with a report which will help you see how your air compressor(s) are being controlled, how much energy they are using, and how much air flow and pressure your system is using. Recommendations can be made to help you reduce your operating costs and return those losses back into profit for your business. Small adjustments can reduce your operating pressure and energy costs while improving flow rates and output. Here are 10 steps you can take to optimize your compressed air system and save energy costs.
- Turn It Off.
There are 168 hours in a week, but most compressed air systems only run at or near full capacity between 60-100 hours. Depending on your shift pattern, turning your compressors off during the evenings and weekends could reduce your energy bills up to 20 percent.
How can FSC features and benefits help with this step? Here’s a suggestion to help you turn off your compressor effortlessly. Look into the FS Curtis Nx Series of Air Compressors using the i-Command® Touch Control. This advanced compressor controller can be set to turn off your air compressor at the end of a shift or workday automatically. Another energy-saving option i-Command® Touch Control is to allow the system to reduce the system pressure during non-production hours. Let’s say you operate several CNC machines which need to keep 80 psi in order to maintain the tool settings. So your i-Command ® Touch Control can be set to reduce the system pressure down to the 80 psi range during your off shifts. This saves you electric costs because for every 2 psi you can drop your system pressure, you reduce your electric costs by 1%. So that 20 psi reduction just reduced your electric usage by 10% for the non-productive hours…
- Fix Existing Leaks.
A quarter-inch air leak at 100 psi will cost you more than $2,500 a year. Pipe systems, hose connections, and filter/regulator housings older than five years can have leaks of up to 25 percent. Because it takes energy to generate compressed air, any air that leaks is money wasted. Approximately 80 percent of air leaks are not audible, so to minimize these problems, third-party help in detecting these leaks may be a necessity.
How can FSC features and benefits help with this step? Your local FS Curtis Distributor can help you with a leak survey using an ultra-sonic leak detector. They can find leaks in your system and pneumatic equipment without shutting down your production. The survey will provide you with a list of items needing attention and repair. Your utility may offer a cost-sharing program to help pay for the survey. You can have your maintenance team make the repairs or have your FS Curtis Distributor make the repairs.
- Prevent New Leaks.
As Benjamin Franklin said, “An ounce of prevention is worth a pound of cure.” So, be proactive and look inside your piping system. A clean, dry pipe indicates good quality air and no corrosion issues. Dust in the pipe is caused by particles in the compressed air. If compressed air is not filtered, or if the filter is clogged, pressure drops will occur and the risk of end product contamination will increase. Sludge in the pipe is bad news and must be fixed immediately. Dust and sludge in a compressed air piping system will cause corrosion very quickly and will greatly increase the number of leaks. Dried and filtered compressed air keeps piping clean.
How can FSC features and benefits help with this step? Your FS Curtis Distributor will often recommend installing a Flow Meter at the point where your compressed air leaves the compressor room and flows to the “Demand Side” of your air system. Some Flow Meters can be tied into your building’s data logging equipment. If you don’t have a data logging system, just setting up a simple log sheet so when your maintenance staff make their daily check on the air compressor, they can write down the flow rate seen on the Flow Meter screen. If you start to see an increase in the Flow numbers, it’s time to start to investigate. Did you add new equipment that takes more air? Did a process change? If nothing changed, its time to look for air leaks again!
- Reduce Pressure. Run at required pressures, not beyond.
Each two psi reduction cuts energy consumption one percent. Check the system pressure and resist the urge to turn up the pressure to compensate for leaks or drops in pressure due to piping problems or clogged filters. A central supply side controller can greatly reduce the operational pressure band and orchestrate air production much more efficiently and effectively.
How can FSC features and benefits help with this step? Your FS Curtis Distributor is a good resource to help you. They can help you establish a pressure profile of your facility. Let them help you find what process or equipment is needing the highest pressure. Often we find air supply systems running at 15 to 50 psi higher than what is really needed. A simple DemandSmart® Flow Controller may help you manage your demand side pressure and flow. Not only will you reduce your energy bill, but your facility may have less wear on air tools and improve your product quality due to a constant air pressure in our plant. Have your FS Curtis Distributor include checking needed down-stream point of use filters for pressure drop and clogged filters. Sometimes folks crank up the pressure to get more pressure to the equipment, when a change in the filter element is really needed.
- Check Drains. Are your condensate drains stuck open?
Condensate drains on timers should be adjusted periodically to ensure they open as intended or aren't stuck open. Better yet, replace timer drains with zero-loss drains to stop wasting compressed air.
How can FSC features and benefits help with this step? First, when you purchasing a new air compressor select an energy saving zero-loss drain. While the zero-loss drain may have a higher investment price, you will not be losing compressed air every time the timer opens the drain valve. The opening of the timer drain can cause the compressor to come on for a short period of time causing an unneeded motor start and extra wear on the air compressor. Always make sure your FS Curtis Distributor is checking your auto drains for correct operation when they are doing your scheduled maintenance.
This is a question that a business owner should ask… What can I do to reduce the cost of operating my Compressed Air System?
For years now, the whole industrial world has been listening to the experts that want to help you reduce your electric bill by selling you a more energy lighting system, heating and air conditioning system, speed controlled pumps, and automatic “do-dads” that promise a lower power bill. The air compressor industry has been drawn into this energy-saving charge because in most facilities, the electric motor in the compressed air system can be the largest and most powerful electric device in the building. So the air compressor has become one of the favorite targets of the utilities wanting to reduce the peak load on a local power grid. You’ve heard all of the sales pitches now from both the compressor guys and the power companies. But there may be low-cost actions you can take to make your compressed air system more efficient and further reduce your monthly electric bill.
First, find ways to reduce your existing air systems’ operating costs. You may not need to pay for an air system audit unless you don’t have the time or experienced staff to conduct your own system assessment. Sometimes, just focusing your facilities manager on reducing the cost of the compressed air system can work. Sometimes having a trusted air compressor vendor works well. And sometimes you may need the help of a paid compressed air auditor if you’re budget allows. However, as a starting point, there are some things you can do on your own first.
According to CAGI, the most expensive component in the total cost of compressed air is energy. In fact, over the lifespan of a typical compressor, energy typically costs several times more than the purchase price of the compressor. The bottom line, maximizing energy efficiency saves you money.
At the beginning, you must know what your compressed air system is doing and why.
- What is the highest pressure required by your equipment and processes?
- What equipment and processes require the highest pressure?
- What machine or process truly needs that much pressure and flow?
- How clean and pure must your compressed air supply be in order to not cause product “do-over’s” caused by water or oil in the air lines?
- What is the lowest and the highest rate of flow to the demand side of the piping system, and what causes the increased demand for flow?
If you can’t answer these basic questions for your compressed air system, then you really don’t understand or manage your compressed air system effectively. And you are probably wasting a lot of money that could easily be turned into profit dollars.
The first step to reducing compressed air energy costs is to measure and monitor your compressed air system's energy consumption, flow rates and operating air pressure. Your FS-Curtis Distributor can help you with your understanding of your compressed air system through an assessment or audit of your system. The FS-Curtis Distributor will provide you with a report which will help you see how your air compressor(s) are being controlled, how much energy they are using, and how much air flow and pressure your system is using. Recommendations can be made to help your reduce your operating costs and return those losses back into profit for your business. Small adjustments can reduce your operating pressure and energy costs while improving flow rates and output.
Learn about the 10 Steps to Saving Compressed Air System Operating Costs (1-5)
Pro Compressor, Allentown, Pennsylvania has been in business since 1994. Bob Dietrick owns the successful independent compressor house and has built his loyal customer base by providing exceptional service at competitive prices. Pro Compressor as been an FS-Curtis Distributor serving the Leigh Valley region of Eastern Pennsylvania since they opened for business.
Dietrick began his career in the air compressor industry in the late 70’s selling Joy compressors and Wilkerson air dryers and filters. In the mid 80’s he formed a business with a partner selling Champion and Grimmerschmidt compressors. Then in 1994, Bob started Pro Compressor in his garage at home, building on his loyal customer base and expertise in keeping his customers compressors in top working condition. He selected Curtis Compressors to be his main brand and has been selling FS-Curtis products since that time. As the business grew, he moved operations to the present location on North New Street in Allentown.
The market served by Pro Compressor is the Leigh Valley region which includes Allentown, down to Philadelphia, and north to Pocono Mountain region. The focuses of Pro Compressor are industrial companies such as: metal processing, electronics, wood products, and food and beverage manufacturers.
Today, Pro Compressor has a staff of 4 full-time employees including 2 field service technicians, an Inside Sales and Customer Service manager, an outside sales engineer (Bob’s main role) and a Part-Time technician. Bob’s son Matt heads up the Service Division. All of Pro Compressor’s technicians are factory trained on all FS-Curtis rotary and reciprocating compressors, as well as FS-Curtis Variable Speed Drive and Electronic controls. So confident in their technical abilities, FS-Curtis regularly calls on Pro Compressor to support customers’ outside of their normal marketing area as needed. Pro Compressor is a valued member of the FS-Curtis Platinum Distributor Council and works with other FS-Curtis Platinum Distributors in advising both marketing and product development projects.
Pro Compressor Web site: http://procompressor.net
Why the FS-Connect Piping System?
Do you have problems with the pressure, flow or quality of your air that is affecting your products, increasing your scrap rate due to rejections in quality, efficiency, tooling costs due to increased maintenance or spraying applications like paint jobs? Then you may want to review your compressed air piping system for a start in enhancing your operation and savings.
What You Need to Consider When Selecting Piping?
- Know your installation & ambient conditions.
Consider the environment the piping system will be installed in. There are many elements that can induce corrosion. Some harsh chemicals or fumes could have an adverse effect on the pipe. Installation conditions could play a role in the effectiveness of your system and life cycle of the pipe.
- Know your flow, the temperature and the pressure min and max requirements.
For safety and overall performance, the flow, the temperature and the pressure should be reviewed and discussed thoroughly before a choice of pipe is made.
- Review the budget and plan for possible expansion in the future.
All pipe options have different price points, different installation requirements and options for future expansion. It’s best to consider all of these factors before choosing the product that will be best for your installation.
The benefit of the FS-Connect Piping System (aluminum) is ease of installation at an extremely competitive cost advantage when compared to traditional piping systems. Our system offers non-plastic fittings for durability and many different mounting brackets to handle all the installation requirements for any location. The FS-Connect Piping is simple, cost-effective and will impact your compressed air system and bottom-line in a positive manner.
As with anything there are always many ways to accomplish the same end result, just with differing energy, thought and cost to get that same end result. If you can have the best quality of air with the least amount of headaches and least amount of waste in terms of production and maintenance for the least cost, wouldn’t you choose that solution? If you are interested in savings and ease of mind the FS-Connect Piping System offers the most flexibility for design and install over all of the other technologies. No sweating is required as with copper piping, no threading, pipe dope and labor intensive cutting and hanging as with the black malleable piping. The copper and black pipe is very heavy and cumbersome to handle making for costly, labor eating installations. The shipping and handling that is involved in the traditional pipe drives the costs even higher. These other technologies also need the special tooling required for the projects. Aside from the installation drawbacks of black pipe and copper pipe one must also be aware of the corrosion that starts attacking these piping materials from the onset. Copper is not nearly as bad from a corrosion point compared to black iron piping, however copper still corrodes over time and does have the high cost factor for installations due to the rising price of copper and labor to sweat.
The Benefits of Using FS-Connect Piping System
The FS-Curtis Aluminum Piping System’s benefits include:
• Energy efficient
• Lower installation costs
• Push-to-connect technology
• Immediate pressurization
• Removable and reusable
• Modular design
• No corrosion
• Leak-free guarantee
• Full bore design
• 1/2" - 6" pipe sizes
FS-Curtis now has aluminum piping up to 6”!
The FS-Curtis team, in a partnership with Parker Transair, has worked hard to bring you a full line of push-to-connect aluminum piping, tools, and fittings. Parker Transair is easy to use, high quality, and well known throughout the globe.
The FS-Curtis Piping System’s benefits include:
• Energy efficient
• Lower installation costs
• Push-to-connect technology
• Immediate pressurization
• Removable and reusable
• Modular design
• No corrosion
• Leak-free guarantee
• Full bore design
• 1/2" - 6" pipe sizes
Learn more about our FS-Curtis Piping System!
For questions or support quoting the right product for your job, contact an Authorized FS-Curtis Distributor.